Fimer PVS-50-TL Скачать руководство пользователя страница 85

Страница: 85 / 171

000872BG-F

5 - Installation

For both type of connection, proceed to connect all the units of the RS485

chain in accordance with the daisy-chain model observing the correspon-

dence between the signals, and activate the termination resistance of the

communication line in the final element of the chain by switching:

- the

switch for the RS485-1 line in the ON position.

- the

switch for the RS485-2 line in the ON position.

PVS-60

Monitoring

system

RS485-1 120

120

TERM.

RS485

RS485-2 120

OFF

RS485-1 120

OFF

RS485-2 120

OFF

RS485-1 120

OFF

RS485-2 120

The communication line must also be terminated on the first element of the chain which nor

mally corresponds to the monitoring device.
It is recommended not to exceed a length of 1000m for the communication line.

The maximum number of inverters that can be connected to the same RS485 line is 62.

When connecting a single inverter to the monitoring system, activate the

communication line resistance terminal by setting the switch

(to

the ON position).

Set a different RS485 address on each inverter in the chain.

No inver-

ter can have “Auto” as an address

. An address can be freely chosen

between 2 and 63.

The setting of the address on the inverter is done through the "Aurora

Manager" software.

When an RS-485 connection is being used, if one or more inverters are

added to the system at a later time, it is necessary to remember to reset

to OFF the switch on the termination resistance being used (1) or (2) on

the inverter which previously was the last in the system.

Each inverter is shipped with the RS485 address pre-set to two (2) and

with the resistance terminal setting switch

in the OFF position.

J18

J10

J11

J12

J16

J14

J13

J20

J17

J21

J18

J24

J27

J19

J22

J25

J15

5 6

COM

5 6

OFF

PC2

OFF

PC1

J18

J10

J11

J12

J16

J14

J13

J20

J17

J21

J18

J24

J27

J19

J22

J25

J15

5 6

COM

5 6

OFF

PC2

OFF

PC1

RS485-1 120

RS485-2 120

RS485-1 120

RS485-2 120

OFF

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды