Fimer PVS-50-TL Скачать руководство пользователя страница 54

Страница: 54 / 171

000866CG-F

5 - Installation

• Respect the minimum distances from objects around the inverter that

could prevent the inverter installation and restrict or block the air flow.

• Provide sufficient working space in front of the inverter that allows to

make connections on the wiring box.

• In case of multiple installation position the inverters side by side keeping

the minimum distances (measured from the outer edge of the inverter)

for each inverter.

• If the space available does not allow this arrangement, position the in-

verters in a staggered arrangement as shown in the figure so that heat

dissipation is not affected by other inverters below.

• The vertical installation is also permitted on a structure which must be

composed of a support for the attachment of the bracket and one for the

support of the rear pins.

• The vertical installation of two inverters positioned back to back is also

permitted on a structure which must be composed of a support for the

attachment of the brackets and one for the support of the rear pins.

Please refer to the warranty terms and conditions to evaluate any possible warranty exclu-

sions due to improper installation.

5° MAX

PVS-6

PVS-

PVS-60

5° MAX

50cm

20cm

50cm

30cm

5° MAX

PVS-6

PVS-

PVS-60

5° MAX

50cm

20cm

50cm

30cm

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды