Fimer PVS-50-TL Скачать руководство пользователя страница 170

Страница: 170 / 171

170

000704AG-F

9 - Attachments

Network Hosts

The inverter will connect to the following hosts. Some servers owned by

FIMER, and others are customer or ISP servers. Servers listed as ow

ned by “Customer IT/ISP” must be configured in the inverter using either

DHCP or as static network information.

Host

Purpose

Port

Owner/Manager

platform.auroravision.net

Data, configuration

TCP:443

FIMER

gw1.auroravision.net and/or

apt.fatspaniel.net

Inverter firmware upgrade

TCP:443

FIMER

Site dependent

DHCP (optional)

UDP:67,

UDP:68

Customer IT/ISP

Site dependent

DNS

UDP:53,

TCP:53

Customer IT/ISP

Inverter network configuration

The inverter requires a valid network configuration in order to operate.

This information can either be provided by a DHCP server provided by

the customers network (the default), or the inverter can be configured

with static network information. Regardless of how the inverter is confi

gured, the following information is required.

Configuration

Purpose

IP Address

Allows the inverter to take part in the local network. This does not need to

be a public IP address. In most cases this is a private IP address.

Subnet mask

Used to determine if two computers are on the same network.

Gateway

The IP address of the computer which will forward network traffic from the

local network to an external network

DNS Server

The IP address(es) of the computer(s) which resolve domain names.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды