Fimer PVS-50-TL Скачать руководство пользователя страница 154

Страница: 154 / 171

154

000761AG-F

8 - Maintenance

- Error code

- Error message

- Warning

Name of Alarm and Cause

Solution

E053

- AFDD Fault

Yellow LED

Arc Fault board autotest failed:

Problem detected during the AFDD board autotest

phase.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E054

- AFDD comm. Fault

Yellow LED

Arc Fault board communication error:

Error on the RS485 serial communication detected

between the inverter and the AFDD board.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E055

- AFDD wrong conf.

Yellow LED

Arc Fault board parameter reading error:

Error in the parameter reading by the system.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E056

- Over Temp. (from

external box)

Yellow LED

Excessive temperature measured inside the inver-

ter's wiring box:

High internal temperature.

This error relates to the temperature measured on

external boxes (e.g.:TRIO-20.0/27.6kW).

• Check that the inverter is not exposed to direct sunlight. Wait

for the temperatures to which the inverter is exposed to return

to the operating range and for the inverter to cool down.

- If the problem persists (once the ambient temperature has

returned to within the range), contact customer assistance.

Remember to wait the time needed to allow the inverter to

cool down

E057

- Vbulk reading error

Yellow LED

Input voltage (Vin) higher than booster voltage

(Vbulk):

The error occurs if the input voltage exceeds the

Bulk voltage (voltage on the DC-DC circuit inside the

inverter)

• It is necessary to measure the input voltage inside the inver-

ter with a voltmeter.

- If it is higher than the maximum voltage of the operating

range, the alarm is genuine and it is necessary to check the

configuration of the PV generator. If the voltage has also

exceeded the maximum input threshold the inverter could be

damaged.

- If it is lower than the maximum voltage of the operating

range, the alarm is caused by an internal malfunction and it is

necessary to contact customer assistance.

E058

- Pin vs Pout check

error

Yellow LED

Error in the check of Pin vs Pout:

The error occurs if the difference between the measu-

red value of input power and that of output power is

greater than the limit imposed internally to the inverter.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E065

- Stop Button

Yellow LED

Emergency (stop) button activated:

This code marks the activation of the emergency

button (button pressed). This warning is activated only

where there is DC or AC voltage as, if the emergency

button is pressed while it is operating only by battery,

it causes the whole system to shut down.

• Check that the emergency button has been pressed and if

necessary deactivate it.

- If the warning persists even though the button has been

deactivated, contact customer assistance.

E066

- Charger-Bulk

Yellow LED

Error in the “Charger” circuit:

Error internal to inverter relating to the bulk voltage of

the circuit linked to battery charger

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E067

- Charger - OV

Yellow LED

Overvoltage of "battery charger" ("Charger"

circuit):

Error inside the inverter. The alarm is raised when

the battery charger voltage exceeds the overvoltage

threshold (internal unchangeable threshold).

• The error might continue when the battery is disconnected

(e.g. activation of emergency button).

• If the message persists and is not linked to the battery being

disconnected, contact customer assistance.

E068

- Charger - OC

Yellow LED

Overcurrent of "battery charger" ("Charger"

circuit):

Error inside the inverter.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E069

- Charger-SlowRamp

Yellow LED

Error internal to inverter linked to the battery pack

charger circuit ("Charger" circuit"):

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E070

- Charger-preChar.

Yellow LED

Error inside the inverter.

• Error inside the inverter probably linked to the fuse in the

damaged battery pack; the error cannot be verified externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E074

- Internal error

Yellow LED

Communication error inside the inverter:

The alarm occurs when there are communication pro-

blems between the control devices inside the inverter.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E077

- Internal Error

Yellow LED

Error in the system configuration:

Error inside the inverter

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

E078

- Riso Test fail

Yellow LED

Riso test error:

Problem detected during the Riso test phase.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched

off and back on again), contact customer assistance.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды