background image

162

000880BG-F

8 - Maintenance

Replacing DC string fuses

Some inverter parts may be subject to voltages that could be hazardous for the operator. Be-

fore performing any work on the inverter, refer to “Inverter switch-off” chapter on this manual to 

know all the necessary step to safely operate on the inverter.

The string protection fuses (where present) in the inverter may need to 

be replaced in the following circumstances:

1. Adjustment of the fuse value on the basis of the type of PV panels used

2. Damaged fuse

Procedure for replacing string fuses from positive 

35

 or negative 

34

 (only 

on -SX, -SX2 model) string fuses board:

PVS-50-TL-SX

PVS-60-TL-SX

PVS-60-TL-SX-CN

PVS-50-TL-SX2

PVS-60-TL-SX2

35

35

34

1.

 Open any AC disconnect switch downstream of the inverter.

2.

 Open the DC disconnect switches 

15

By only disconnecting the AC disconnect switch and the DC disconnect switch, the DC input 

voltage is still present on the fuse board. Use adequate PPE (personal protective equipment).

3.

  Disconnect the strings by disconnectiong the quick fit input connectors 

19

 

20

 

21

.

4.

  Wait enough time for the stored energy to be discharged (min time 30 

minutes).

5. 

Open the wiring box front cover 

04

6.

 Remove the fuse to be replaced

7.

 Introduce the new fuse into the fuse holder on the string fuse boards

Содержание PVS-50-TL












































































































































































Отзывы: