Fimer PVS-50-TL Скачать руководство пользователя страница 69

Страница: 69 / 171

000870BG-F

5 - Installation

Independent channel configuration (default configuration)

In the inverter -SX and -SX2 versions, the independent configuration of

the input channels (MPPT) is set at the factory. This means that the pa

rallel bar (supplied) must not be installed on the parallel MPPT connec

tion points

, and that the software setting “Independent channel mode”

should be performed on the inverter; this setting can be done by different

way:

1. During the commissioning wizard phase (STEP 4)

2. In the dedicated section of the internal webserver “

Setup section >

Setup DC side > Input mode

”

3. Using the inverter display (if available) on the dedicated menu

“

Inverter>Settings> Input mode

”.

This configuration is not available for Standard and -S versions of the

inverter.

Parallel channel configuration

In the inverter -SX and -SX2 versions, the configuration of the input chan

nels (MPPT) can be set in parallel.

Before carrying out this configu

ration, disconnect the strings from the inverter and open the AC

disconnector.

This means that the parallel bar (supplied) must be in

stalled on the parallel MPPT connection points

, and that the software

setting “parallel channel mode” should be performed on the inverter; this

setting can be done by different way:

1. During the commissioning wizard phase (STEP 4)

2. In the dedicated section of the internal webserver “

Setup section >

Setup DC side > Input mode

”

3. Using the inverter display (if available) on the dedicated menu

“

Inverter>Settings> Input mode

”.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды