Fimer PVS-50-TL Скачать руководство пользователя страница 91

Страница: 91 / 171

000874AG-F

6 - Instruments

User interface

1. Embedded Web User Interface

• Accessible via Wi-Fi by using any WLAN enabled standard device

(PC, smartphone, tabled,….)

• Enables single inverter parameters settings (Aurora Manager Em-

bedded)

• Updating of the inverter firmware.

2. Local display

• Just for reading settings

• Enabled setting RS485 ports addresses and MPPT functioning mode

• Available on request (it is an accessory)

3. Aurora Manager Lite

• Mainly for service purpose

• Local monitoring of the inverter.

• Advanced configuration of the inverter (INSTALLER access level)

• Updating of the inverter firmware.

• In order to use the software a connection must be established be-

tween the PC and the inverter (by means of an RS485 communica-

tion line) using a PVI-USB-RS485_232 signal converter.

4. Mobile app and web portal Aurora Vision

• Remote monitoring of the inverter.

Measurement tolerance

The data supplied by the inverter may differ from measurements taken

by certified measuring instruments (e.g. output meters, multimeters and

grid analysers); since the inverter is not a measuring instrument it has

wider tolerances for the measurements it makes.

The tolerances are generally:

±5% for real-time measurements with output power below 20%

±3% for real-time measurements with output power above 20%

±4% for all statistical data.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды