Fimer PVS-50-TL Скачать руководство пользователя страница 107

Страница: 107 / 171

107

000876AG-F

7 - Operation

LED status

Operating state

green:

yellow:

red:

• Ventilation anomaly

Indicates ananomaly in the operation of the internal ventilation system that could limit output

power at high ambient temperatures.

• Overvoltage surge arresters triggered

Indicates that any class II overvoltage surge arresters installed on the AC or DC side have

been triggered

• Autotest not executed (only for Italian network standards)

On the inverter was not performed the Autotest

• Internal statistics memory anomaly

Indicates an operating anomaly in the internal memory on which the inverter statistics are

stored

• Buffer battery discharged

The buffer battery is low and the inverter does not maintain the time setting

green:

yellow:

red:

• Initial configuration failure

The inverter is in locked state due to a failure in the initial configuration of the equipment,

such as the standard network setting for the country of installation

• Self-test not carried out (for Italian grid standards only)

Self-test operation failure

Incompatibility of the device firmware versions

The firmware versions of the various devices comprising the equipment are incompatible

and are being updated (this is an automatic operation)

•Temperature sensor anomaly detected

green:

yellow:

red:

Updating the firmware from an SD card

The equipment firmware is being updated from an SD card

* lighting of

the LEDs in

sequence

Firmware programming failure

There has been a failure in programming the firmware, of one or more internal devices of the

equipment, to the equipment from an SD card.

green:

yellow:

red:

Updating the firmware from an SD card completed

The equipment firmware has been successfully updated from an SD card

green:

yellow:

red:

Updating the firmware from an SD card has failed

The equipment firmware update from an SD card has failed

*blink 3 times

green:

yellow:

red:

Remote OFF activated

The Remote Off command has been activated.

The unit will not connect to the network until the remote ON command has been activated

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды