Fimer PVS-50-TL Скачать руководство пользователя страница 111

Страница: 111 / 171

111

000877BG-F

7 - Operation

Web User Interface menu structure

The following screenshots are related from a laptop visualization, may differ from smartphone

or tablet visualization.

The Web User Interface is divided in six main sections, available on the

left sidebar:

MAIN:

Main section of Web User Interface dedicated to viewing the sum-

mary informations related the status and the production informations of

the inverter and photovoltaic plant.

SETTING:

Section dedicated to AC and DC line parameters configura

tions.

INVERTER LOG:

Section dedicated to viewing Alarms and Warnings

event log.

USER:

Section dedicated to User management.

NETWORK SERVICES:

Section dedicated to inverter communication

settings and configurations.

SERVICE TOOLS:

Section dedicated to main service tools configura

tions.

INFORMATION:

Section dedicated for general informations about the

embedded Web User Interface.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды