Fimer PVS-50-TL Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 171

background image

83

000872BG-F

5 - Installation

Serial Communication connection - Slave (RS485-1, RS485-2)

Be advise that automatic settings of network parameters at the turning on, embedded log

-

ging capability, automatic logger free transferring of data to Aurora Vision Cloud and remote

firmware update are provided over TCP/IP (Ethernet and/or Wi-fi) bus only.
The use of the inverters over the RS485 line is recommended in case of monitoring and con

-

trolling by using third party RS485 control systems.

The connection of the inverters over this RS485 line is recommended for replacement of

already installed old model of inverters or service purpose only.

- RS485-1 serial communication line.

The communication protocol can be set as “Aurora” (proprietary com-

munication protocol) or Modbus RTU (FIMER protocol).

This port must be used for firmware upgrading (locally or remo

-

tely through the FIMER monitoring devices)

When connecting the FIMER monitoring devices, the RS485-1 line must be used

- RS485-2 serial communication line.

The communication protocol can be set as “Aurora” (proprietary com-

munication protocol), Modbus RTU (FIMER protocol) or Modbus RTU

(Sunspec protocol).

Cables connecting the RS485 line may use two different types of con-

nection:

• Connection of the conductors using the

terminal connectors

53

For long distance connections, the connection on terminal connector

is preferable using a shielded twisted pair cable with characteristic

impedance of Z0=120 Ohm like the one shown on the following table:

Signal

Symbol

-T/R

+T/R

SH

RTN

-T/R

+T/R

SH

RTN

Positive data

RS485 (-1 or -2) +T/R

Negative data

RS485 (-1 or -2) -T/R

Reference

RTN

Screen

SH

Shield continuity must be provided along the communication line using the SH terminal and

must be grounded at a single point.

RS485-2

RS485-1

IN

OUT

IN

OUT

(A)

(B)

(A)

(B)

RS485-1

RS485-2

57

56

53

«
...
81
82
83
84
85
...
»

Содержание PVS-50-TL












































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PVS-50-TL

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Mackie Страницы: 18

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 8

Бренд: Mackie Страницы: 7

Бренд: M-Audio Страницы: 25

Бренд: FARM-MAXX Страницы: 35

Бренд: Össur Страницы: 98

Flex Foot Cheetah

Бренд: Össur Страницы: 107

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 39

Bionic Symbionic Leg

Бренд: Össur Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды