Fimer PVS-50-TL Скачать руководство пользователя страница 94

Страница: 94 / 171

000875BG-F

7 - Operation

Commissioning via Installer for Solar Inverters mobile APP

“Installer for Solar Inverters” is the new advanced FIMER mobile APP al-

lows to simplify commissioning, parameter settings and troubleshooting

of FIMER string multi-inverters in large scale solar plants.
Even in case of single inverter installation it can be consider the most

suitable professional tool to be used.
“Installer for Solar Inverters” mobile APP is available for mobile devices

with an Android version of 6.0.1 or greather (iOS mobile devices support

will come soon) and could be downloaded and installed from Play Store.

Commissioning procedure:

It’s higly recommended to connect the inverters in ethernet daisy chain

(with or without ring) before executing the commissioning procedure.

Make sure that all the inverter being commissioned features the last

firmware version (updating can be executed via Installer for Solar Inver

ters mobile APP).

• Close the DC disconnect switches

to supply the inverter with input

voltage from the photovoltaic generator.

Make sure irradiation is stable and adequate for the inverter commissioning procedure to be

completed.

The main steps to complete the commissioning procedures are listed below:

- Installer for Solar Inverters mobile APP installed on mobile device.

- Enabled Aurora Vision installer account allowed to use the mobile APP

The account can be created in the mobile APP directly following the dedicated

wizard procedure.

- Manual claiming of the inverters to be commissioned.
The claiming process consists of indicating which inverters are to be commis-

sioned.
Claiming process can be executed by scanning the QR codes of all the inver-

ters being worked and putting the selected inverters into the working list. Please

insert in the list inverters belonging to the same inverters family; no more than

40 inverters by time can be configured together.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды