EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 766 / 887

background image

Warranty

756

88000 Series

Service and Repairs

Service and Repairs

EXFO commits to providing product service and repair for five years
following the date of purchase.

To send any equipment for service or repair:
1.

Call one of EXFO’s authorized service centers (see

Centers Worldwide

on page 757). Support personnel will determine if

the equipment requires service, repair, or calibration.

2.

If equipment must be returned to EXFO or an authorized service
center, support personnel will issue a Return Merchandise
Authorization (RMA) number and provide an address for return.

3.

If possible, back up your data before sending the unit for repair.

4.

Pack the equipment in its original shipping material. Be sure to include
a statement or report fully detailing the defect and the conditions under
which it was observed.

5.

Return the equipment, prepaid, to the address given to you by support
personnel. Be sure to write the RMA number on the shipping slip.

EXFO

will refuse and return any package that does not bear an RMA number.

Note:

A test setup fee will apply to any returned unit that, after test, is found to
meet the applicable specifications.

After repair, the equipment will be returned with a repair report. If the
equipment is not under warranty, you will be invoiced for the cost
appearing on this report. EXFO will pay return-to-customer shipping costs
for equipment under warranty. Shipping insurance is at your expense.

Routine recalibration is not included in any of the warranty plans. Since
calibrations/verifications are not covered by the basic or extended
warranties, you may elect to purchase FlexCare Calibration/Verification
Packages for a definite period of time. Contact an authorized service center
(see

EXFO Service Centers Worldwide

«
...
764
765
766
767
768
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: Ebyte Страницы: 34

Бренд: YASKAWA Страницы: 61

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

Бренд: Bartec Страницы: 26

Бренд: V2 Страницы: 48

Бренд: Datavideo Страницы: 17

Бренд: Datamax Страницы: 22

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: Fantech Страницы: 2

Бренд: LAE electronic Страницы: 7

Бренд: LAE electronic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды