EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 354 / 887

background image

Test Setup - Test Configurator, Timer, and System

344

88000 Series

Signal - Signal Configuration (OTN)



Tributary Port

, configurable when the

Fixed Structure

check box

is cleared, allows selecting the

Tributary Port

number that will be

associated to the selected tributary slots. When the

Fixed

Structure

check box is selected, the

Tributary Port

is

automatically assigned to either the selected slot number or for
OPU3 to the first slot number in the column.



Nominal Bit Rate (Gbit/s)

available with ODUflex and

ODUflex/GFP-F indicates the TX frequency based on the number of
tributary slots selected. Note that for ODUflex with pattern Client,
the

Nominal Bit Rate

may be affected by the

TX Rate

when not set

to 100 % (see

TX Rate



Number of Trib Slots

indicates the number of tributary slots

selected.

Note:

Tributary slots must be selected starting with the higher layer down to the
lower and all required tributary slots must be selected to access the next
level.

Clear All

,

Select All

, and

Default

buttons may be used to facilitate

the selection.



Config TCM

Allows enabling each TCM level (1 to 6) individually. All ODUx of a
mapped signal are also available. All TCM check boxes are cleared by
default (disabled). Refer to

on page 370 for more

information. Not available with Multi-Channel OTN.

«
...
352
353
354
355
356
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: zipwake Страницы: 12

Бренд: Watts Страницы: 2

Бренд: jbc Страницы: 12

Бренд: Falcon Страницы: 3

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: Zolix Instruments Страницы: 22

Бренд: Radarcan Страницы: 40

Бренд: Baccara Страницы: 16

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Datavideo Страницы: 17

Бренд: Datamax Страницы: 22

Бренд: Van Air Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды