EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 329 / 887

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

319

Services - L2CP

Services - L2CP

The EtherSAM test application supports the configuration of up to 10
different services individually. All parameters are configurable per service.

From the

Test

menu, tap

Setup

,

Test Configurator

, tap on the services

block, and on the

L2CP

tab.

Service Selection and L2CP Handling Test



Service Name

indicates the name to the selected service. Select the

service to be configured by either using the left/right arrow or by
tapping over the service numbers area then tapping on a specific
service number. An orange background indicates the selected service
while a green background indicates the services that are enabled.



L2CP Handling Test

check box when selected (default) enables the

L2CP Handling test for the selected service.

Table

The following parameters are displayed and/or configurable per service.



Check boxes:

The first check box (top-left) allows enabling/disabling all L2CP frames
at once.

The check box in front of each L2CP name allows enabling/disabling
each L2CP frame individually; enabled by default for predefined
frames and disabled for user defined frames.



Name

indicates the name of each L2CP frame.



Destination MAC address

indicates the L2CP frame destination MAC

address.



Expected L2CP Handling

selects the expected L2CP handling for each

L2CP frame:

Pass Through

(default) or

Discard/Peer

.

«
...
327
328
329
330
331
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Yardney Страницы: 8

Бренд: Calsense Страницы: 74

Бренд: Panamax Страницы: 16

Бренд: Netro Страницы: 14

M-DUINO PLUS series

Бренд: Industrial Shields Страницы: 46

Бренд: Pangolin Страницы: 35

Бренд: Sames Страницы: 84

UNDER CONTROL CP-28

Бренд: G-Force Страницы: 2

Бренд: Pestill Страницы: 4

Бренд: FEAM Страницы: 14

Markoprint iJET

Бренд: Weber Страницы: 127

Easyflow J7 DN15

Бренд: Neles Страницы: 12

Бренд: D+H Страницы: 16

Бренд: CompuPro Страницы: 33

Бренд: Hansen Страницы: 4

Allen-Bradley 1784-KT2/B

Бренд: Rockwell Automation Страницы: 32

SR-ZV9002T4-CCT-RU

Бренд: Z-Wave Alliance Страницы: 10

Бренд: Badger Meter Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды