EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 250 / 887

Test Setup - Test Configurator, Timer, and System

240

88000 Series

Link OAM

Link OAM

From the test menu, tap

Setup

Test Configurator

, and the

Link-OAM (802.3

) test block.

OAM Mode

Allows the selection of the OAM mode:



Active

(default) initiates the OAM discovery and send OAMPDU

loopback control; doesn’t respond to variable request nor generate
Link Event Notification.



Passive

doesn’t initiate OAM discovery nor send OAMPDU loopback

control.

OAMPDU Destination MAC Address

Indicates and allows changing the default multicast OAM PDU destination
MAC address:

01:80:C2:00:00:02

Default

check box when cleared (default is selected), allows the

configuration of the OAM PDU destination MAC address:

00:00:00:00:00:00

FF:FF:FF:FF:FF:FF

Pass/Fail Verdict

Pass/Fail Verdict

check box when selected (default) enables the use of the

pass/fail verdict. A global fail verdict is declared when any of the following
condition is met:

Link Down

, any Link OAM alarm,

Remote Alarms

(if

enabled), or

Remote Loopback

(if enabled).



Remote Alarms

check box when selected (default) considers the

following alarms to declare the pass/fail verdict:

Critical Event

Dying

Gasp

, and

Link Fault



Remote Loopback

check box when selected (default) considers

successful/unsuccessful remote loopback request to declare the
pass/fail verdict.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды