EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 476 / 887

Test Results

466

88000 Series

Alarms/Errors Overview

VT/TU

Alarms



AIS-V

(Alarm Indication Signal - VT) - SONET

TU-AIS

(Tributary Unit - Alarm Indication Signal) - SDH

: V1 and V2 bytes for the VT/TU path contain an all-ones pattern in

three (SONET) / five (SDH) consecutive superframes.

: Generates an all-ones pattern for the V1 and V2 bytes of the VT/TU

path and payload.



LOP-V

(Loss Of Pointer - VT) - SONET

TU-LOP

(Tributary Unit - Loss Of Pointer) - SDH

: A valid pointer is not found in N consecutive superframes (where



10), or if N consecutive NDFs (“1001” pattern).

: Generates a non-valid pointer.



RDI-V

(Remote Defect Indication - VT) - SONET

LP-RDI

(Tributary Unit - Remote Defect Indication) - SDH

: Bit 8 of the V5 byte contains “1” in five consecutive VT/TU

superframes while bits 6 and 7 of the Z7 (SONET) / K4 (SDH) byte
contain the “00” or “11” pattern.

: Generates “1” for the bit 8 of the V5 byte and a “00” pattern for bits

6 and 7 of the Z7 (SONET) / K4 (SDH) byte.



RFI-V

(Remote Failure Indication - VT) - SONET

LP-RFI

(LOP - Remote Failure Indication) - SDH, available with VC-11

only.

: Bit 4 of the V5 byte contains “1” in five consecutive superframes.

: Generates “1” for the bit 4 of the V5 byte.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды