EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 327 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

317

Services - Global



Frame Size

indicates the frame size of each service. Tap on the

Frame

Size

button to modify the frame size of each service.



Framing

indicates the framing of each service. Tap on the

Framing

button to modify the

Frame Format

Network Layer

Transport Layer

VLAN

S-OAM MEG/MD Level

, and

MPLS

when applicable (see

Modify

Frame Structure

from the

MAC/IP/UDP

on page 247).



VLAN (ID/Priority)

indicates the ID and Priority of each VLAN level for

each service. Tap on the

VLAN

button to modify the VLAN settings (see

VLAN

from the

MAC/IP/UDP

on page 247).



Addressing

indicates the source and destination IP or MAC addresses

for each services. Tap on the

Addressing

button to modify the

addressing (see

MAC

and

from the

MAC/IP/UDP

on page 247).

Batch

button allows bulk configuration for services addressing. Select

the check box of each configuration parameter that needs to be copied
and set its parameters. From

Apply To

, select all services the copy

applies to and tap on the

Copy From

to proceed.

SLA Button

The SLA parameters are displayed and configurable per service. Click on
the desired column button to access the configuration settings.

See

General Button

on page 316 for more information on check boxes,

Direction

, and

Service Name

See

SLA Parameters

on page 325 for more information on

CIR

CIR+EIR

CBS

EBS

Max Jitter

Max Latency

, and

Frame Loss Rate

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды