EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 257 / 887

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

247

MAC/IP/UDP

MAC/IP/UDP

Note:

Only available with Framed Layer 2 (see

Framing

).

From the

Test

menu, tap

Setup

,

Test Configurator

, and...



For

RFC 2544

and

EtherBERT

, tap on the protocol block.



For

EtherSAM

, and

Traffic Gen & Mon

, tap on the protocol block, and

on the

MAC/IP/UDP

tab.



For

FlexE BERT

, tap on the

Clients

block, and on the

MAC

tab.



For

eCPRI BERT

, tap on the

eCPRI FLow

block, and on the

MAC

tab.

Stream (Traffic Gen & Mon) / Service (EtherSAM)
Selection

Traffic Gen & Mon supports the configuration of up to 16 different streams.
EtherSAM supports the configuration of up to 10 different services.

Select the stream/service to be configured by either using the left/right
arrow or by tapping over the stream/service numbers area then on a
specific number.

Client ID and Size (FlexE BERT)



Client ID

allows selecting the client ID to be displayed.



Size (Gbit/s)

indicates the size of the client.

Couple with Interface

The

Frame Format

,

Network Layer

, and all

IP

and

VLAN

settings are

coupled with the interface (see

on page 264) when the

Couple

with Interface

check box is selected (default). The

Source

MAC Address

is always coupled. Not available when using

Provider Encapsulation

.

«
...
255
256
257
258
259
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Hanna Instruments Страницы: 88

Бренд: Taoglas Страницы: 2

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренд: YASKAWA Страницы: 66

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA Страницы: 58

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренд: iluminize Страницы: 2

Бренд: Matelec Страницы: 16

Бренд: Reliance Foundry Страницы: 3

Бренд: Wesa Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды