EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 201 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

191

EtherSAM - Burst

EtherSAM - Burst

Note:

The

Burst

settings are only available for configuration when the

Burst Test

check box is selected (see page 193).

From the

Test

menu, tap

Setup

Test Configurator

, tap on the test block,

and on the

Burst

tab.

Note:

The burst configuration parameters are defined globally for all services but

CBS

EBS

, and

Burst Max Rate

parameters are as per each service

configuration.

Burst Sequence

The graphic illustrates the configured burst sequence that contains in
order, from left to right:



Refill Delay

represents the pre-burst recuperation time in percentage

that is equal to the remaining percentage not used by the post-burt
time (

Refill Delay Ratio



Burst Frames

represents the burst frame ratio in percentage that is

equal to the substraction of

100 % - Burst/IR Frame Ratio



Refill Delay

represents the post-burst recuperation time in percentage

that is equal to the configured

Refill Delay Ratio



CIR or CIR+EIR Frames

represents the percentage of transmission at

CIR or CIR+EIR rate. The

CIR or CIR+EIR Frames

percentage is equal

to the configured

Burst/IR Frame Ratio



The “. . .” next to the burst sequence indicates that the burst sequence
is repeated the number of times specified in the

Number of Burst

Sequence

field.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды