EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 464 / 887

background image

Test Results

454

88000 Series

Alarms/Errors Overview



Unexp MEP

(Unexpected MEP)

RX

: A CCM frame was received from the peer MEP with same MEG/MD

Level, correct MEG ID/MAID, and correct source MAC Address
(corresponds to the peer MEP) but with unexpected MEP ID. The alarm
is cleared when no CCM frames with same MEG/MD Level, correct
MEG ID/MAID, correct source MAC Address (corresponds to the peer
MEP) but with an unexpected MEP ID are received within an interval
equal to 3.5 times the configured CCM transmission period.



Unexp Period

(Unexpected Period)

RX

: A CCM frame is received from the peer MEP with same MEG/MD

Level, correct MEG ID/MAID, and correct MEP ID but with a period field
value different than the one configured. The alarm is cleared when no
CCM frames with same MEG/MD Level, correct MEG ID/MAID, and
correct MEP ID but with incorrect period field value are received within
an interval equal to 3.5 times the configured CCM transmission period.



RDI

(Remote Defect Indication)

RX

: The RDI flag bit of a valid CCM frames is set to 1. A valid CCM frame

has its source MAC address matching the Peer MEP MAC address, the
destination MAC address matching either the unit port Unicast MAC
address or a Multicast class 1 address (refer to page 841), and VLANs
matching the unit port VLANs.

TX

: The RDI flag bit of transmitted CCM frames is set to 1.

«
...
462
463
464
465
466
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Radio Shack Страницы: 52

Бренд: Abus Страницы: 12

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Mackie Страницы: 16

Бренд: TANDBERG Страницы: 47

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: National Instruments Страницы: 2

Бренд: OES Страницы: 3

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренд: YASKAWA Страницы: 30

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

Бренд: Coris Страницы: 4

MS6-SV-...-D-10V24

Бренд: Festool Страницы: 32

Бренд: SOMFY Страницы: 56

Бренд: ACL Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды