EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 326 / 887

background image

Test Setup - Test Configurator, Timer, and System

316

88000 Series

Services - Global

Services - Global

From the

Test

menu, tap

Setup

,

Test Configurator

, tap on the services

block, the

Global

tab, and on the

General

button.

General Button

The following parameters are displayed and configurable per service.



Check boxes:



The first check box (top-left) allows enabling sequentially
service(s) within the limit of the link capacity when the

Service

Performance Test

is enabled or enabling all services when the

Service Performance Test

is disabled.



The check boxes next to the service numbers allow enabling each
service individually.

When the

Service Performance Test

is enabled, up to 10 services

can be enabled one after the other, as long as the

Total TX Rate

(bandwidth) is not reached (

Committed

). For example, if the first

service is using the full bandwidth available, then no other service
can be enabled. If the first enabled service uses half bandwidth,
then at least another service can be enabled using up to half
bandwidth. Thus, to enable a second service, first set the CIR value
within the non-used bandwidth (

Available

), then enable it.

When the

Service Performance Test

is disabled, up to 10 services

can be enabled one after the other; the total TX rate is not limited.



Service Name

indicates the name of each service. Tap on the

Service

Name

button to modify the name of each service. See

Services - Profile

for more information.



Direction

, available with

Dual Test Set

or

Dual Port

topology,

indicates respectively results for local (

L

) and remote (

R

) directions, or

for both port directions.

«
...
324
325
326
327
328
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Acclaim Lighting Страницы: 32

Бренд: Yudian Страницы: 26

Бренд: Eaton Страницы: 100

Бренд: Oceanic Страницы: 11

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Watts Страницы: 4

Бренд: Climatisation Страницы: 52

Бренд: TECOM Страницы: 8

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

Бренд: Lauda Страницы: 40

Бренд: Megalarm Страницы: 2

Бренд: Srne Страницы: 13

MU System X Dual Amplifier

Бренд: Frequency Central Страницы: 4

Бренд: Sysmac Страницы: 159

Бренд: tams elektronik Страницы: 20

Бренд: Gira Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды