EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 268 / 887

background image

Test Setup - Test Configurator, Timer, and System

258

88000 Series

MAC/IP/UDP



Global IPv6 Address

(GUA) is used to communicate with on-link

neighbors and for global communication with hosts outside the
subnet.



Mode

None

disables the

Global IPv6 Address

and the

Default Gateway

Address

.

Stateless Auto

(default) allows automatic generation of the IPv6

address based on the Link-Local address interface ID and the
prefix obtained from the router advertisements. If no Interface ID
has been obtained for the

Link Local Address,

the global address

will not be generated.

Static

allows entering the IP address.



Address

, available with

Static

mode, allows selecting the

Global

IPv6 Address

. The accepted range is from

0000:0000:0000:0000::[Interface ID]

to

FFFF:FFFF:FFFF:FFFF::[Interface ID]

. The default address is

2001:0000:0000:0000::[Interface ID]

, where [

Interface ID

] is

generated from the source MAC address. When the

Address

field

is selected for editing using virtual keyboard, the

Previous IPs

button appears allowing the selection of a previously configured IP
address.



Interface ID Coupled

, available when the

Source Global IPv6

Address

mode is

Static

, allows coupling the interface ID of the

Global address to the Link-Local source address.

Enabled

(default): Only the 64 bit (MSB) prefix ID in the IPv6

address is configurable, and the 64 bit (LSB) Interface ID is not
configurable (read-only).

Disabled

: The 64 bit (MSB) Prefix ID and 64 bit (LSB) Interface ID

in the IPv6 address are configurable.

«
...
266
267
268
269
270
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: QUAD Страницы: 16

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: Samson Страницы: 78

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

FAREX SR MINI SYSTEM

Бренд: RKC INSTRUMENT Страницы: 82

Бренд: M-system Страницы: 7

Бренд: SMC Networks Страницы: 10

Бренд: K&K Страницы: 10

MorphoAccess VP MD

Бренд: Idemia Страницы: 29

Бренд: Forcepoint Страницы: 15

VPPM-...-LK Series

Бренд: Festo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды