EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 206 / 887

background image

Test Setup - Test Configurator, Timer, and System

196

88000 Series

EtherSAM - Global



Burst Test

check box when selected (cleared by default) verifies

that the expected burst size can be transmitted at maximum burst
rate with minimal loss.

CBS

(Committed Burst Size) check box when selected (see

on page 325), verifies the performance of a committed

burst size at

CIR

’s average

TX

rate.

EBS

(Excess Burst Size) check box when selected (see

on page 325), verifies the performance of an excess

burst size at

CIR+EIR’s

average

TX

rate.

The maximum Jitter, Latency, Frame Loss, and throughput are
measured. For

CBS

, the Jitter, Latency, and Frame Loss are

compared to the SLA thresholds to declare a pass/fail verdict. For

EBS

, the throughput is compared to the SLA thresholds to declare

a pass/fail verdict.

The burst test procedure is performed for each enabled service.



Service Performance Test

check box when selected (default) verifies

that the

SLA

parameters (see

SLA Parameters

are met

over time by running multiple services simultaneously. The maximum
Jitter, Latency, Frame Loss, and average throughput are measured and
compared to the configured thresholds to declare pass/fail verdicts.
The

Service Performance Test

is only performed for services that have

their

CIR

check box selected.

Subtest Duration

allows setting the duration time, in HH:MM:SS

format, for the

Service Performance Test

(default is 10 minutes).



Global Test Duration Estimate

indicates the total estimate duration of

the test.

«
...
204
205
206
207
208
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Hankscraft Runxin Страницы: 53

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: RadioMaster Страницы: 10

Бренд: Xblue Networks Страницы: 2

Бренд: Absima Страницы: 5

Бренд: RKC INSTRUMENT Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды