EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 732 / 887

Test Control

722

88000 Series

Discover Remote Button



Loop UP/Down



Loop Up

establishes the connection with the selected remote unit

and loopback mode is set and initiated on the remote unit.

Following a successful loop up, the MAC and IP addresses of the
remote unit will be used as the destination addresses for the test.

Once the connection is established with the remote unit, the local
unit can be set for EtherSAM, RFC 2544, EtherBERT, or
Traffic Gen & Mon testing.

A message is displayed if the remote cannot be reached.



Loop Down

ends the connection between the local and the

remote units.

Local Module Identification

Module ID

is used to easily identify this unit in case another unit is

performing a discovery scan. Up to 16 alpha-numeric characters are
allowed.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды