EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 290 / 887

background image

Test Setup - Test Configurator, Timer, and System

280

88000 Series

ODU Channels - Global

Bit Error



Pass/Fail Verdict

allows enabling bit-error-rate pass/fail verdict by

selecting either

Bit Error Count

or

Bit Error Rate

. The default value is

Disabled

.



BER Threshold

allows entering the threshold

Count

or

Rate

value that

will be used to declare the pass/fail verdict.

For

Count

, enter the maximum bit error count allowed before

declaring a fail verdict:

0

(default) to

999999

.

For

Rate

, enter the maximum bit error rate allowed before declaring a

fail verdict:

1.0E-14

to

1.9E-01

. The default value is

1.0E-12

.

Service Disruption

The Service Disruption Time (SDT) corresponds to the duration associated
to a defect that occurred in the network. For example a disruption that
occurs during a network switching from the active channels to the backup
channels or vice versa.



Disruption Monitoring

check box when selected (disabled by

default) enables the disruption time measurements. However, the
measurement will only start if the test is already started, or when the
test is started.

Note:

Clearing the

Disruption Monitoring

check box will stop the measurement

without clearing the results. The disruption monitoring is automatically
stopped without clearing results when the test is stopped. However, starting
the test again while the

Disruption Monitoring

check box is selected will

reset the results before restarting.

Note:

The service disruption measurements are cleared when changing the
criteria.

«
...
288
289
290
291
292
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: D-Link Страницы: 40

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Rane Страницы: 2

Бренд: Samson Страницы: 78

Бренд: Parkside Страницы: 86

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: NAiS Страницы: 144

Бренд: Paradox Страницы: 3

Бренд: National Instruments Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды