EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 646 / 887

background image

Test Functions

636

88000 Series

FDL - Bit-Oriented Message

Receive Messages



Link Activity

indicates the activity of the following parameters during

the last second of measurement.



Idle

indicates that only idle codes have been detected in the last

second.



Priority

indicates that at least one valid priority message has been

detected in the last second.



C/R

(Command/Response) indicates that a least one valid

command and response has been detected in the last second.



Unassigned

indicates that at least one unassigned message has

been detected in the last second. Therefore, since an unassigned
message is part of a Command/Response codewords, the
Command/Response LED will also be red.



PRM

indicates that at least one PRM has been detected in the last

second.



Priority

: The Bit-Oriented Messages are priority messages send over

the Data-Link. These messages are mostly used for networking
operation and maintenance. A Bit-Oriented Message consists of
8 consecutive 1s followed by a byte starting and ending by zeros.

Current

indicates the priority message detected in the last second. If

no priority message has been detected, “--” is displayed.

Previous

indicates the last priority message detected excluding the

current message. If no priority message has been detected since the
beginning of the test, “--” is displayed.

Note:

See

on page 634 for the list of possible priority codeword messages.

«
...
644
645
646
647
648
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Lawler Страницы: 5

Бренд: Rain Bird Страницы: 48

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: Kärcher Страницы: 4

Бренд: Uniden Страницы: 28

Бренд: UniFocus Страницы: 23

Бренд: UniFocus Страницы: 6

Бренд: Ultraflex Страницы: 7

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

Бренд: Tamiya Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды