EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 191 / 887

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

181

eCPRI Flow - Profile



Measurement Rate

, available with

Sender

measurement role,

defines the number of Latency/Jitter measurements to perform per
second:

1 Measurements/s

.



Frame Loss/Out-of-Sequence

check box, when selected (default),

allows Frame Loss and Out-of-Sequence monitoring.

Remote

Status Sender Receiver

Description

Ready-R

X

X

Indicates that one-way delay flows normally
between sender and receiver for both
request/response and remote request/request

Mismatch-R

X

-

Indicates, for Sender measurement role, that
the remote end is also configured as Sender.

Inactive-R

X

X

Indicates that there is no one-way delay
message received within 5 seconds that can be
caused by: a Link Down condition, an LOPPS-L
being present on the local or peer device, both
ends configured as Receiver, or incompatible
framing.

--

X

X

Indicates pending state which occurs upon
starting a test or when a Link Down condition
is detected.

«
...
189
190
191
192
193
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: OmarLift Страницы: 14

Бренд: GBD Страницы: 68

Бренд: BADLANDS Страницы: 2

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 2

Бренд: Dantherm Страницы: 20

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренд: micro-trak Страницы: 44

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: A.R.I. Страницы: 14

Бренд: Industrial Controls Страницы: 17

Бренд: SolarEdge Страницы: 20

Бренд: Veichi Electric Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды