EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 715 / 887

Test Functions

Power Blazer

705

RTD/RTT (CPRI/OBSAI Framed L2)

Round Trip Delay (CPRI)

Indicates the time required for a bit to travel from one point to another.



Delay T14

indicates the round trip delay measurement from the Base

Station going through the Remote Radio Head (including

Toffset

) and

back to the Base Station. The

Delay T14

appearing on the diagram

corresponds to the average value.



Cable Delay

indicates the cable delay measured from the Base Station

to the Remote Radio Head (RRH) or vice-versa assuming that the
cabling in both directions are the same. The

Cable Delay

appearing on

the diagram corresponds to the average value.



Last

indicates the result of the last delay measurement.



Minimum

indicates the minimum delay recorded.



Maximum

indicates the maximum delay recorded.



Average

indicates the average delay value.



Unit

measurement selections are

(default) and



Toffset

allows the configuration of the internal delay introduced by the

electronic components in the Radio Equipment (RE): 0

s (default) to

66.67

Note:

A warning icon appears next to the

Toffset

value when this value is larger

than the

Delay T14

value measured indicating that the

Toffset

configured

value maybe invalid thus corrupting the

Cable Delay

values reported.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды