EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 410 / 887

Test Results

400

88000 Series

Alarms/Errors Overview

DS3

Alarms



AIS

(Alarm Indication Signal)

: The M-frame contains zeros (0) for C-bits, ones (1) for X-bits,

1010... repeating sequence with a one (1) immediately following any of
the control bit positions for the information bits.



Idle

(DS3 Idle)

: Subframe 3 of the M-frame contains zeros (0) for the three C-bits,

ones (1) for X-bits, 1100... repeating sequence with the first two bits
following each control bit set to 11 for the information bits.



OOF

(Out-OF-Frame)

: Four consecutive frame bit errors are detected.



RDI

(Remote Defect Indicator)

: Both X-bits of the M-Frame are set to “0”.

Errors



CP-Bit

(Control-Bit)

: The three C-bits reserved to control bit stuffing are different of

“111” and “000”.



F-Bit

(Framing-Bit)

: The frame alignment pattern received is different of “1001”.



P-Bit

(Parity-Bit)

: The P-Bits does not match the parity of all the information bits

following the first X-Bit of the previous DS3 frame.



FEBE

(Far-End Block Error)

: The three FEBE bits reserved for framing or parity error detection

contain the “000” pattern.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды