EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 92 / 887

Test Setup - Test Applications

88000 Series

Carrier Ethernet OAM

Carrier Ethernet OAM

The Carrier Ethernet OAM test application supports the following tests:

Ethernet OAM (S-OAM)

MPLS-TP OAM

, and

Link OAM

Ethernet OAM and MPLS TP OAM

The Ethernet Service OAM tests are divided into two main categories:



Performance Monitoring measures parameters such as frame delay,
frame loss, and synthetic loss (Y.1731/MEF).



Connectivity Fault Management provides the capability for detecting,
verifying, and isolating connectivity failure (Y.1731/802.1ag/MEF).



Typical Ethernet OAM and MPLS TP OAM test applications:



Supported Interfaces/Rates: 10M to 10G LAN/WAN.

MIP

EXFO Unit

Peer MEP

Local MEP

MIP

EXFO Unit

Local MEP

EXFO Unit

Smart Loopback with

S-OAM Responder enabled.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды