EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 679 / 887

background image

Test Functions

Power Blazer

669

OH - SONET/SDH



B2

: BIP-8

SONET: The BIP-8 (Bit-Interleaved Parity) byte provides line error
monitoring. This byte is only defined for the first STS-1/STM-1 frame of a
composite signal. The byte is calculated by performing a routine
even-parity check over all bits of the LOH and the STS-1 frame capacity
of the previous frame of a composite signal (STS-1 to STS-n). Note that
the SOH is not used to calculate the parity check.

SDH: The MS BIP-N*24 (Bit-Interleaved Parity) byte provides line error
monitoring. The byte is calculated by performing a routine even-parity
check over all bits of the MSOH and the STM-N frame of the previous
STM-N frame. Note that the RSOH is not used to calculate the parity
check.



K1

and

K2

: Automatic Protection Switching (APS): The K1 and K2 bytes

communicate APS between two LTE. These bytes are only defined for
the first STS-1/STM-1 frame of a composite signal.



D4

through

D12

: Data Communications Channel (DCC): The D4

through D12 bytes provide a 576 Kbit/s data communications channel
between two LTEs for administration, monitoring and other
communications. These bytes are only defined for the first STS-1/STM-1
frame of a composite signal.



S1/Z1 (SONET)

S1

: Synchronization Status: The S1 byte is used to carry the

synchronization status of the SONET device. This byte is only defined
for the first STS-1/STM-1 frame of a composite signal.

Z1

: Growth. This byte is located in the second STS-1 through STS-n

frame of a composite signal (STS-1 #2, STS-1 #3, up to STS-1 #N of a
OC-N (N>3) signal).



S1

(SDH): Synchronization Status. Bits 5 to 8 of the S1 byte are used to

carry the synchronization messages of the SDH device. This byte is only
defined for the first STS-1/STM-1 frame of a composite signal.

«
...
677
678
679
680
681
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: UNITED Страницы: 22

Бренд: Datalogic Страницы: 15

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 400

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 466

Бренд: Waterway Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды