EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 106 / 887

background image

Selecting and Starting a Test

96

88000 Series

Intelligent Apps

3b.

From the

Network

block, either select the basic test parameters

or click on

More

for all settings (refer to

Network Details (iSAM)

on page 269). The total bandwidth and the estimated test duration
are displayed.

3c.

Select the remote operation mode; DTS is automatically selected
when the

RFC 6349 Test

is enabled:

3d.

From the

Remote

block, either select the basic remote

parameters or click on

More

for all settings (refer to

Details (iSAM)

Note:

The iSAM test application uses

Internal

timing for clock synchronization.

4.

Tap the

Start

button from the right navigation bar to start the test (refer

to

Start/Stop|TX Button

on page 741). If the connection with the

remote module is not established with either

DTS

or

Remote

Loopback

mode, the automatic remote connection process is

performed before starting the test. The

Summary

result page will be

automatically displayed when the test is started from any

Setup

configuration page. For additional results refer to

5.

When the test ends automatically or is manually stopped, the generate
report pop-up is displayed by default. If required, tap

Yes

to generate a

report of the test results and statistics (refer to

Report Button

page 731 for more information).

DTS (Dual Test Set)
The remote device is automatically set in EtherSAM when the
connection/overtake is successfully established.
Remote Loopback
The remote device is automatically set in Smart Loopback when the
connection/overtake is successfully established.
Manual Loopback
The remote device is a physical loopback or has to be manually set in
loopback.

«
...
104
105
106
107
108
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: KELCO Страницы: 36

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 157

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: Daruifuno Страницы: 24

MT600iWP Series

Бренд: weintek Страницы: 2

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Infi 90 IMSPM01

Бренд: Bailey Страницы: 52

Бренд: Heat & Cool Страницы: 5

Бренд: Viper Страницы: 2

Бренд: Bartec Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды