EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 751 / 887

background image

Test Control

Power Blazer

741

Start/Stop|TX Button

Start/Stop|TX Button

The

Start/Stop|TX

button allows starting or stopping manually any test as

well as enabling traffic generation.

To start the test:

Tap the

Start

button to start the test.

Start

is available when the test is

not running.

To stop the test:

Tap the

Stop

button to stop the test; the traffic generation also stops if it

was enabled (TX button).

Stop

is available when the test is running.

By default, a message is displayed when the test stops asking to
generate a report. To disable this feature, see

Turn on Report

Generation

on page 733. Nothing prevents the configuration and

alarm/error injection setup while the test has been stopped; thus, if a
report is required, it should be saved before changing any test
parameters to avoid discrepancy between the configuration and
results. See

Report Button

on page 731 to generate and save a report.

To enable traffic generation:

Tap the

TX

button to enable traffic generation; the test is also started if

it was not running.

Note:

While the test is running the

TX

button is available to enable/disable traffic

generation.

Test Application

Descripton

Traffic Gen & Mon

Enables traffic generation for all enabled streams.
Some conditions, such as ARP not resolved, link down, etc., may prevent the stream to
be transmitted.

FlexE BERT

Enables traffic generation for all enabled clients (refer to Enable TX from

eCPRI BERT

Enables traffic generation.

«
...
749
750
751
752
753
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: TCS Страницы: 16

Бренд: Trane Technologies Страницы: 8

Бренд: SMC Networks Страницы: 10

Saxun Mosquito Screen Lateral Door 2020

Бренд: Gimenez Ganga Страницы: 2

Бренд: Keysight Technologies Страницы: 78

Бренд: Barco Страницы: 4

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 142

Бренд: Calmotion Страницы: 9

Wireless Security Keychain Remote

Бренд: Radio Shack Страницы: 2

Бренд: Curtis Страницы: 30

Бренд: VADDIO Страницы: 16

Бренд: Dukane Страницы: 30

Бренд: EMC2 Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды