EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 203 / 887

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

193

EtherSAM - Global

EtherSAM - Global

From the

Test

menu, tap

Setup

,

Test Configurator

, tap on the test block,

and on the

Global

tab.

Dual Test Set



Dual Test Set

(

DTS

) check box when selected (cleared by default)

enables EtherSAM

Dual Test Set

. Once

Dual Test Set

is enabled, use

the

Discover Remote

button to select a remote unit. Not available in

Dual Port

topology.

Note:

It is also possible using the Discover Remote button to connect to a remote
module and automatically enable Dual Test Set. For more details, refer to

Discover Remote Button



Disconnected

indicates that there is no connection established

with a remote

module

.



NAT LAN/WAN

and

WAN IP

indicate presence of NAT (Network

Address Translation) router. The NAT router is automatically
detected and graphically displayed with LAN/WAN indication as
well as the WAN IP address when the

module

is behind a NAT

router.

Note:

When there is a NAT at the Remote site, it is required to create UDP/TCP
port 62819 forwarding rule on this NAT router to allow DTS communication.
In addition, when there is a NAT in both directions (L->R and R->L), it is
also required to create port forwarding rules on the NAT router located at
the Remote side for every service defined.



Discover Remote

button allows discovering remote

module

supporting

Remote Loopback

and/or

Dual Test Set

. For more details,

Discover Remote Button

«
...
201
202
203
204
205
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Febco Страницы: 12

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренд: Quectel Страницы: 90

Бренд: TCS Страницы: 16

Бренд: Vega Страницы: 20

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: FUTABA Страницы: 8

Бренд: Vertiv Страницы: 2

Бренд: Quantum Страницы: 20

Бренд: PS Automation Страницы: 4

Saxun Mosquito Screen Lateral Door 2020

Бренд: Gimenez Ganga Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды