EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 728 / 887

background image

Test Control

718

88000 Series

Discover Remote Button

Discover Remote Button

The Discover Remote function allows performing Ethernet tests in
conjunction with a second test set (unit) by either scanning and
connecting to any available EXFO Datacom remote unit or connecting to a
third party remote device in loopback mode. The remote unit is used to
loop back the traffic; for an EXFO unit it could be via Smart Loopback or

Dual Test Set

(DTS) for simultaneous bidirectional RFC 2544, RFC 6349, or

EtherSAM results.

Note:

Only available with single-port

EtherSAM

,

EtherBERT

,

RFC 2544

,

RFC 6349

, and

Traffic Gen & Mon

test applications.

Remote Module Type

Allows selecting the loopback type for EtherSAM, EtherBERT, RFC 2544,
and Traffic Gen & Mon test applications. For other test applications, this
setting is forced to

EXFO

.



EXFO

(default), see

Remote Modules Discovery (EXFO)



Third-Party Loopback

Remote Modules Discovery (3rd Party

Remote Modules Discovery (EXFO)



Target

defines how to perform the scan to discover remote units.



Subnet

indicates to perform the scan based on the current subnet.



Specific IP

indicates to perform the scan for a specific remote unit

IP address. Enter the IP address of the target unit.

Quick Ping

tests if the destination IP address can be reached. A

message displays if the ping attempt is

Successful

or

Failed

.



Scan

button scans the subnet or a specific IP (see

Target

) to discover

remote EXFO compatible unit(s).

«
...
726
727
728
729
730
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Slim Remote Control

Бренд: Packard Bell Страницы: 2

Бренд: Unipower Страницы: 24

Бренд: Parkside Страницы: 65

Бренд: Balboa Страницы: 23

Бренд: Balboa Страницы: 2

MusicCAST MCX-CA15

Бренд: Yamaha Страницы: 176

Бренд: M-system Страницы: 3

Бренд: Dantel Страницы: 6

GAMMA VERSUS Series

Бренд: JCM Страницы: 111

767-4804/000-800

Бренд: WAGO Страницы: 80

Бренд: Alde Страницы: 36

YQPV-HP360V/100A

Бренд: PSC Solar Страницы: 22

Бренд: GEM Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды