Epson S1C17001 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 351

background image

11 16-BIT TIMER (T16)

116

EPSON

S1C17001 TECHNICAL MANUAL

11.8 16-bit Timer Interrupts

The 16-bit timer outputs interrupt requests to the interrupt controller (ITC) when the counter underflows.
To generate a timer underflow interrupt, the interrupt level and interrupt permission should be set using the ITC
registers.

Timer interrupt ITC registers

Table 11.8.1 lists the ITC control registers for each timer channel.

Table 11.8.1: ITC registers

Timer channel

Interrupt flag

Interrupt enable bit

Interrupt level setting bit

Ch.0

IIFT1 (D9/ITC_IFLG)

IIEN1 (D9/ITC_EN)

IILV1[2:0] (D[10:8]/ITC_ILV0)

Ch.1

IIFT2 (D10/ITC_IFLG)

IIEN2 (D10/ITC_EN)

IILV2[2:0] (D[2:0]/ITC_ILV1)

Ch.2

IIFT3 (D11/ITC_IFLG)

IIEN3 (D11/ITC_EN)

IILV3[2:0] (D[10:8]/ITC_ILV1)

ITC_IFLG register (0x4300)
ITC_EN register (0x4302)
ITC_ILV0 register (0x430e)
ITC_ILV1 register (0x4310)

If an underflow occurs in the timer, the corresponding interrupt flag is set to 1.

If the interrupt enable bit corresponding to that interrupt flag is set to 1, the ITC sends an interrupt request to
the S1C17 core. To prohibit timer interrupts, set the interrupt enable bit to 0 beforehand. The interrupt flag will
be set to 1 by the timer underflow pulse regardless of the interrupt enable bit setting (i.e., even if set to 0).

The interrupt level setting bit sets the timer interrupt level (0 to 7). If set to the same interrupt level, the 16-bit
timer Ch.0 takes the highest priority, while the 16-bit timer Ch.2 takes the lowest priority.

The S1C17 core accepts interrupts when all of the following conditions are satisfied:
• The interrupt enable bit has been set to 1.
• The PSR (S1C17 core internal processor status register) IE (interrupt enable) bit has been set to 1.
• The timer interrupt has a higher interrupt level set than that set for the PSR IL (interrupt level).
• No other interrupt factors having higher precedence (e.g., NMI) are present.

For more information on these interrupt control registers and operations when interrupts occur, see “6 Interrupt
Controller (ITC).”

Interrupt vectors

The timer interrupt vector numbers and vector addresses are listed below.

Table 11.8.2: Timer interrupt vectors

Timer channel

Vector number

Vector address

Timer Ch.0

13 (0x0d)

0x8034

Timer Ch.1

14 (0x0e)

0x8038

Timer Ch.2

15 (0x0f)

0x803c

«
...
123
124
125
126
127
...
»

Содержание S1C17001
































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C17001

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Parkside Страницы: 86

Бренд: Netafim Страницы: 4

Бренд: TREND Страницы: 12

Бренд: Z-Wave Страницы: 3

Бренд: Danfoss Страницы: 36

SCENE MASTER - V1.0

Бренд: JBSYSTEMS Light Страницы: 24

Бренд: CALEFFI Страницы: 14

SR-ZV9002T4-CCT-RU

Бренд: Z-Wave Alliance Страницы: 10

Бренд: Advanced Control Technologies Страницы: 3

Бренд: Magnetek Страницы: 19

Бренд: Aruba Networks Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Kilews Страницы: 11

Бренд: Kilews Страницы: 26

Бренд: DAV TECH Страницы: 22

Бренд: Barco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды