Endress+Hauser Gammapilot M FMG60 Скачать руководство пользователя страница 24

Страница: 24 / 104

Wiring

Gammapilot M FMG60 PROFIBUS PA

Hauser

4.5

PROFIBUS PA cable specifications

Twisted, shielded pairs must be used. The following specification must be met for explosion

hazardous application (EN 50 020, FISCO model):

• Loop-resistance (DC): 15 to 150



/km

• Specific inductance: 0.4 to 1 mH/km

• Specific capacitance: 80 to 200 nF/km
The following cable types can be used, for example:
Non-Ex-area:

• Siemens 6XV1 830-5BH10 (black)

• Kerpen CEL-PE/OSCR/PVC/FRLA FB-02YS(ST)YFL (gray)

• Belden 3076F (orange)
Ex-area:

• Siemens 6XV1 830-5AH10 (blue)

• Belden 3076F

• Kerpen CEL-PE/OSCR/PVC/FRLA FB-02YS(ST+C)YFL (blue)

4.6

Supply voltage

The following values are the voltages across the terminals directly at the device:

Approx. 11 mA for the range of voltages given above.

4.7

Potential equalization

CAUTION

Applications, which are subject to the explosion prevention, permit only under special

conditions the repeated grounding of the protective screen , see to EN 60079-14.

Type

Minimum terminal voltage

Maximum terminal voltage

Standard

9 V

32 V

Ex ia (FISCO model)

9 V

17.5 V

Ex ia (Entity concept)

9 V

24 V

For maximum EMC protection please observe the

following points:

• The external ground terminal on the

transmitter must be connected to ground.

The cable should be kept as short as possible for

optimum electromagnetic compatibility. The

use of a grounding strip is ideal.

• The continuity of the cable shielding between

tapping points must be ensured.

• If potential equalization is present between the

individual grounding points, ground the

shielding at each cable end or connect it to the

device housing (as short as possible).

• If there are large differences in potential

between grounding points, the grounding

should run via a capacitor that is suitable for

high frequency use

(e.g. ceramic 10 nF/250 V&).

A0018086

Содержание Gammapilot M FMG60









































































































Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды

Endress+Hauser Gammapilot M FMG60, Руководство по эксплуатации

Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды