Endress+Hauser Gammapilot M FMG60 Скачать руководство пользователя страница 89

Страница: 89 / 104

Gammapilot M FMG60 PROFIBUS PA

Troubleshooting

Hauser

W642 I_back calibration running

Calibration of the current readback path active

A631

background not calibrated

Perform background calibration

(

"calibration" (*1)

function group)

A632

full/covered not calibrated

Perform full/covered calibration
(

"calibration" (*1)

function group)

A633

empty/free not calibrated

Perform empty/free calibration
(

"calibration" (*1)

function group)

A634

density not calibrated

• Check: Has at least one calibration point been entered and

activated?
If not: Enter and activate calibration point(s). (

"calibration"

(*1)

function group)

• Check: Is the "reference pulse rate" (*1F) larger than 2

If yes: re-perform density calibration (

"calibration" (*1)

)

function group

A635

present date not defined

• Enter present date

(

"basic setup" (*0)

function group

"today's date" (*01)

function)

• See Note "

Error messages A165 "electronics defect" and

A635 "present date not defined"



54.

A636

calibration date not plausible

Check calibration date and enter it again

(

"system parameters" (*C)

function group

"calibration date" (*C7)

function)

A637

operating mode not defined

Enter operating mode
("basic setup" (*0) function group

"operating mode" (*04)

function)

A638

measurement mode not defined

Enter measurement mode
("basic setup" (*0) function group

"measurement mode" (*05)

function)

A639

temperature compensation not
complete

Enter at least two "temperature - density" value pairs
(

"temperature compensation" (*3)

function group)

W662 high sensor temperature (warning)

Install water cooling jacket or thermal shielding

A663

sensor temperature too high (alarm)

Install water cooling jacket or thermal shielding

A664

temperature measurement error

Check correct functioning and connection of the PT-100 sensor

W681 current out of range

(3.8 to 20.5 mA)

Check calibration and linearization

A692

gammagraphy detected (alarm)

• Check, if interference radiation is present or the

"hold time"

(*54)

is too short.

• If no interference radiation is present: decrease

gammagraphy sensitivity

(

"gammagraphy" (*5)

function group

"sensitivity" (*52)

function)

W693 gammagraphy detected (warning)

Wait for end of the gammagraphy measurement

W695 measurement counter overflow

The local dose rate is too high (where applicable, reduce with
blind flange).

Code

Description

Remedy

Содержание Gammapilot M FMG60









































































































Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды

Endress+Hauser Gammapilot M FMG60, Руководство по эксплуатации

Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды