Endress+Hauser Gammapilot M FMG60 Скачать руководство пользователя страница 78

Страница: 78 / 104

Commissioning

Gammapilot M FMG60 PROFIBUS PA

Hauser

6.5.4

Linearization (for concentration measurements)

If the concentration is to be measured in a unit other than the

"density unit" (*06)

, a

linearization must be performed after the calibration. This can be done in the

"Linearization" (*4)

function group. The functions of this group and the linearization

procedure are described in Operating Instructions BA00287F/00/EN, "Gammapilot M -

Description of Device Functions". This document can be found on the supplied CD-ROM.

6.5.5

Additional settings

After the calibration, the Gammapilot M outputs the measured value via the PROFIBUS PA

interface.

Many additional functions are available for optimizing the measuring point. They can be

configured as required. A detailed description of all instrument functions is given in

Operating Instructions BA00287F/00/EN, "Gammapilot M - Description of Device

Functions". This document can be found on the supplied CD-ROM.

6.6

Density measurement/temperature-compensated

Perform density measurement as described in the section "Calibration for density and

concentration measurements" and then perform temperature calibration (see "Temperature

compensation" section in BA00287F/00/EN "Gammapilot M - Description of Device

Functions").

6.7

Gammagraphy detection

See "Gammagraphy" section in BA00287F/00/EN "Gammapilot M - Description of Device

Functions".

Содержание Gammapilot M FMG60









































































































Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды

Endress+Hauser Gammapilot M FMG60, Руководство по эксплуатации

Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды