Endress+Hauser Gammapilot M FMG60 Скачать руководство пользователя страница 17

Страница: 17 / 104

Gammapilot M FMG60 PROFIBUS PA

Installation

Hauser

3.3

Water cooling

For the versions of the Gammapilot with water cooling jacket, the following applies:

• Material: 316L

• Water connection: 2 x G 1/4"A, DIN ISO 228

• Inlet temperature: max. 40 °C (104 °F)

• Outlet temperature: max. 50 °C (122 °F) (temperature monitoring recommended)

• Water pressure: 4 to 6 bar (60 to 90 psi)

A0018078

T <75 °C (167 °F)

T <120 °C (248 °F)

CAUTION

Detector or cooling jacket can be damaged if the cooling water freezes.

‣

Empty cooling jacket or protect against freezing.

WARNING

Pressurized water cooling system!

‣

Do not open the cylinder screws (see figure below) when pressurized.

A0023205

Cylinder screws

/4"A

CAUTION

To consider when using the water cooling

jacket

‣

It is recommended to ground the water

cooling jacket separately at the provided

earth terminal (see picture above)

‣

The ambient temperature of the

compartment housing must not exceed

75 °C (167 °F). This is also valid, if water

cooling is applied.

‣

The three screws, connecting the pipe

housing to the compartment housing, must

not

be opened.

A0018068

Содержание Gammapilot M FMG60









































































































Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды

Endress+Hauser Gammapilot M FMG60, Руководство по эксплуатации

Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды