Endress+Hauser Gammapilot M FMG60 Скачать руководство пользователя страница 20

Страница: 20 / 104

Wiring

Gammapilot M FMG60 PROFIBUS PA

Hauser

Wiring

4.1

Terminal compartments

4.2

Cable entries

NOTICE

Cable entries

‣

On delivery, not more than one cable gland is present for each of the terminal

compartments. If further cable glands are required (e.g. for cascading mode), they must

be supplied by the user.

‣

Connecting cables should be routed away from the housing from below to prevent

moisture from penetrating the connection compartment. Otherwise, a drain loop should

be provided or the Gammapilot M should be fitted with a weather protection cover.

The Gammapilot M has got two terminal

compartments:

• Terminal compartment 1, for

– Power supply

– Signal output (depending on the instrument

version)

• Terminal compartment 2, for

– Signal output (depending on the instrument

version)

– PT-100 input (4-wire)

– Pulse input for cascading mode

– Pulse output for cascading mode

– Display and operating module FHX40

(or VU331)

NOTICE

Depending on the instrument version, the

signal output is located in the terminal

compartment 1 or 2.

Maximum cable length:

• For cascade, 20 m (66 ft) each

• For PT-100 2 m (6.6 ft) (temperature should be

measured as close as possible to density

measurement)

A0018082

The number and type of cable entries depend on

the instrument version ordered. The following

types may occur:

• Gland M20x1.5

tightening diameter (clamping range):

7.0 to 10.5 mm

• Cable entry M20x1.5

• Cable entry G1/2

• Cable entry NPT1/2

• M12 connector (see "Fieldbus connectors")

• 7/8" connector (see "Fieldbus connectors")
In addition, Gammapilot M has a socket to

connect the separate display and operating unit

FHX40. The housing of the Gammapilot M does

not have to be opened to connect the FHX40.

A0018083

Cable entries for terminal compartment 2

Socket for FHX40

Cable entries for terminal compartment 1

Содержание Gammapilot M FMG60









































































































Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды

Endress+Hauser Gammapilot M FMG60, Руководство по эксплуатации

Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды