Endress+Hauser Gammapilot M FMG60 Скачать руководство пользователя страница 25

Страница: 25 / 104

Gammapilot M FMG60 PROFIBUS PA

Wiring

Hauser

4.8

Wiring in terminal compartment 1

CAUTION

Before connection please note the following:

‣

When using the instrument in hazardous areas, make sure to comply with national

standards and the specifications in the Safety Instructions (XAs). Make sure you use the

specified cable gland.

‣

The supply voltage must comply to the data on the nameplate.

‣

Switch off power supply before connecting the instrument.

‣

Connect potential matching line to the outer transmitter ground terminal and to the

ground terminal of the water cooling jacket (if present) before connecting up the

instrument (see "Potential equalization",



24).

‣

Connect protective earth to the protective earth terminal (see "Terminal assignment",



21).

‣

According to IEC/EN 61010 a suitable power switch has to be provided for the

instrument.

‣

The cable isolations must comply with the supply voltage and the overvoltage category.

‣

The temperature resistance of the connecting cable must comply with the ambient

temperature.

The procedure

Using a 3 mm Allen key, loosen the

cover clamp for the connection

compartment cover.

Unscrew the cover of the terminal

compartment.

Push the power cable and (if required)

the signal cable) through the

appropriate cable glands or cable

threads.

Wire up according to the terminal

assignment diagram.
Tighten the cable glands or threads.
Screw the cover securely back onto the

terminal compartment..
Adjust the cover clamp so it is set over

the cover and tighten.

A0019826

L1
L+

N
L-

Содержание Gammapilot M FMG60









































































































Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды

Endress+Hauser Gammapilot M FMG60, Руководство по эксплуатации

Результаты поиска

Содержание Gammapilot M FMG60

Отзывы:

Похожие инструкции для Gammapilot M FMG60

Бренды по названию

Популярные бренды