Endress+Hauser analytikjena multi N/C pharma HT Скачать руководство пользователя страница 50

Страница: 50 / 125

Installation and commissioning

multi N/C pharma HT

used for all measurement methods, and in particular for NPOC analysis with parallel
purging. When using different sample trays, the block with the wash cups is simply re-
moved from the autosampler and exchanged.

Figure 31Layout of the AS vario ER autosampler

1 Canula for connection to the sample in-

take hose

2 Canula holder (here with no. 72)

3 Sample tray for 72

4 Ultrapure water bottle

5 Canula flush

6 Canula for connection with the purge

hose for NPOC measurement

Removing the transport locks

The autosampler is secured for transport with a retaining screw on the bottom of the
autosampler. Retain the transport lock for later transport.

Figure 32Transport lock

1 Transport lock

2 M3x12 screw

Содержание analytikjena multi N/C pharma HT






























































































































Результаты поиска

Содержание analytikjena multi N/C pharma HT

Отзывы:

Похожие инструкции для analytikjena multi N/C pharma HT

Бренды по названию

Популярные бренды

Endress+Hauser analytikjena multi N/C pharma HT, Руководство по эксплуатации

Результаты поиска

Содержание analytikjena multi N/C pharma HT

Отзывы:

Похожие инструкции для analytikjena multi N/C pharma HT

Бренды по названию

Популярные бренды