Endress+Hauser analytikjena multi N/C pharma HT Скачать руководство пользователя страница 36

Страница: 36 / 125

Installation and commissioning

multi N/C pharma HT

Installation and commissioning

4.1

Installation conditions

4.1.1

Ambient conditions

This laboratory device is designed for inside use.

Avoid direct sunlight and radiation from heaters onto the device. If necessary, pro-
vide air conditioning.

The installation site must be free of drafts, dust and caustic fumes.

The room air must be as low in TOC and NO

as possible.

Avoid mechanical shocks and vibrations.

Do not locate the device near sources of electromagnetic interference.

Place the device on a heat-resistant and acid-resistant surface.

The device must be positioned in such a way that allows easy access from all sides.

Keep the ventilation slits free and do not obstruct them with other devices.

The following climate requirements apply in the room of operation:

Operating temperature

+10 to 35 °C (air-conditioning recom-
mended)

Maximum humidity

90 % at 30 °C

Air pressure

0.7 to 1.06 bar

Storage temperature

5 to 55 °C

Humidity during storage

10 to 30 % (use desiccant)

Operating altitude (max.)

2000 m

4.1.2

Device layout and space requirements

The basic device has been designed as a compact bench-top device. The required space
depends on all components that make up the measuring station.

Further components of the measuring station:

The PC, monitor and printer may be placed on a separate side table.

An acid-resistant waste container can be placed on or under the bench.

Optional modules:

The AS 10e and AS 21hp autosamplers are attached to the right side wall of the ba-
sic device. Alternatively, the autosamplers can be placed next to the analyzer on the
left.

The AS vario and EPA Sampler autosamplers must be positioned to the right of the
device.

The Swab-Test Module is attached to the left side wall of the basic device.

The CLD nitrogen detector must be positioned to the left of the basic device.

Component

Dimensions (width x height x
depth)

Weight

Basic device

513 x 464 x 550 mm

30 kg

AS 10e autosampler

260 x 390 x 320 mm

4.5 kg

AS 21hp autosampler

260 x 390 x 320 mm

4.5 kg

AS vario autosampler

350 x 470 x 400 mm

15 kg

EPA Sampler

500 x 560 x 400 mm

15 kg

Содержание analytikjena multi N/C pharma HT






























































































































Результаты поиска

Содержание analytikjena multi N/C pharma HT

Отзывы:

Похожие инструкции для analytikjena multi N/C pharma HT

Бренды по названию

Популярные бренды

Endress+Hauser analytikjena multi N/C pharma HT, Руководство по эксплуатации

Результаты поиска

Содержание analytikjena multi N/C pharma HT

Отзывы:

Похожие инструкции для analytikjena multi N/C pharma HT

Бренды по названию

Популярные бренды