ELTRA CS-2000 Скачать руководство пользователя страница 159

Страница: 159 / 160

Index

159

Reason for instability .......................................... 47

Rectifier ............................................................... 24

Rectifier could be faulty ...................................... 24

Removing the IRC-board .................................. 100

Resistance furnace ...............................58, 96, 132

Resistance furnace completly cold or too hot ..... 60

Resistance furnace doesn`t reach full temperature

........................................................................ 62

Resistance furnace takes too long to warm up .. 58

Right hand side view ......................................... 122

Rightt hand side power wiring .......................... 138

Safety warnings .................................................... 7

Sample burns but no peak on the screen ........... 65

serious injury ......................................................... 7

Service ................................................................ 99

Setting the furnace reulation card ....................... 96

Short C path ........................................................ 80

Short S path ........................................................ 80

Single C path ...................................................... 80

Single carbon range ............................................ 80

Single S path ...................................................... 80

Single sulfur range .............................................. 80

Socket top view ................................................... 26

Solenoid valve 2/2 ........................................... 108

Solenoid valves cleaning .................................. 108

Source voltage

rducing............................................................. 81

Spare parts kits ................................................. 148

Spring (36665) which is holding the thermocouple

in place .......................................................... 113

Sulfur results are not repeatable ........................ 36

Supply voltages and thermostatic control circuit 78

Supply voltages for IR signal processing circuit 78,

Temperature control resistance furnace ............. 28

Terminal of the solenoid coil ............................... 46

Test points (general)

IR-Cell ............................................................ 78

Test points IR-ranges......................................... 79

TH 43 ........................................................... 96, 97

TH 44 ........................................................... 96, 97
The filament of the generator tube doesn’t glow 21
The furnace does not close ............................... 30

The results are always 0.0000% or 00.0ppm: ... 37

The tubing ........................................................ 100

Thermocouple replacement ............................. 112

Thermocouple testing ........................................ 98

Thermostatic control reports 0% or 100% power39

Too high noise ................................................... 48

Too low deviation value ..................................... 47

Too low oxygen pressure ............................. 14, 16

TP13................................................................... 20

TP13 test point ................................................... 20

TP9..................................................................... 20

Transformer ....................................................... 40

TRIAC ................................................................ 43

Triac malfunctioning ........................................... 43

Trimmer .............................................................. 85

Tubes to squeeze ............................................ 107

Unstable resistance furnace temperatur ............ 62

Valve wiring ...................................................... 140

Valves .......................................................... 44, 49

Vibrations ........................................................... 64

Vibrations in induction furnace mode ................. 64

Voltage

base-line is too high ....................................... 81
Higher than 9.5V ............................................ 81

Voltage across the heating elements ................. 59

Voltage on the outflow valve is constantly at 24 V

........................................................................ 47

Waiting for stability ....................................... 19, 47

Wiring diagrams ............................................... 137

Содержание CS-2000

































































































































































Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды

ELTRA CS-2000, Руководство по обслуживанию

Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды