ELTRA CS-2000 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 160

background image

Faults

52

When the pulses at TP13 are present without starting analysis and with 12 V DC at TP9, then
the circuit board HF 42 is out of order.

If no scope is available, the pulses can be detected by using a voltmeter.

Normal values are about 0 V AC without pulses, and about 1 V AC with pulses.

This indicated value can be different, depending on the type of the voltmeter used.

If this AC voltage is practically zero but even though the generator is powered, the next possible
reason: The triac is faulty (short circuit), and has to be replaced.

Fig. 40: Circuit board HF 42

Pos : 3. 40 /0025 Übersc hrift en/ELTRA 1.1 Übersc hrift en/11 Cr ucibl e or boat cr ac ks or melts ELTRA @ 6 \mod_1368708007091_9. doc x @ 41231 @ 2 @ 1

3.20 Crucible or boat cracks or melts

Pos : 3. 41 /0010 ELTR A/ 0015 s ervic e_ins truc tions/C S-2000_s er vice/ 05Faults _C S-2000/ 0615 M odul Cr ucibl e cr ac ks or melts @ 9\ mod_1425540955461_9.doc x @ 74357 @ 33 @ 1

3.20.1 Induction furnace

One reason could be that the quality of the crucible is bad. Use a better quality.

Another reason could be that the furnace temperature is too high, due to:

–

Excessive main voltage.

–

Excessive sample and / or accelerator weight.

–

The use of a "sample or accelerator" that requires lower generator power.

In this case reduce the generator power in case of induction furnace. See

chapter „

Induction

generator control

“.

3.20.2 Resitance furnace

In case of resistance furnace, the boat melts when there is excessive amount of metal in the
combustion boat. The dangerous thing is that the molted metal destroys not only the boat but
also the combustion tube, finally dropping thru the tube on the thermocouple. It is then very hard
to remove the deformed tube from the furnace even after breaking it in two.

Pos : 3. 42 /0025 Übersc hrift en/ELTRA 1.1 Übersc hrift en/11 O xygen pres sur e goes up ver y sl owl y @ 9 \ mod_1425548475420_9. doc x @ 74976 @ 2 @ 1

3.21 Oxygen pressure goes up very slowly

Pos : 3. 43 /0010 ELTR A/ 0015 s ervic e_ins truc tions/C S-2000_s er vice/ 05Faults _C S-2000/ 0620Modul T he oxyg en pr ess ure g oes up ver y slowl y @ 9\ mod_1425540999219_9. doc x @ 74369 @ @ 1

When using induction furnace operation:

After the button has been pressed to close the furnace (or to start the analysis by closing the
furnace first ), the oxygen gauge (6) should reach the normal level of

1,5 bar within a couple of seconds after the furnace has closed.

If this takes longer:

Then the problem is most probably outside the analyser.

«
...
50
51
52
53
54
...
»

Содержание CS-2000

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CS-2000

Charge Analyzer 711

Бренд: 3M Страницы: 24

Бренд: Omicron Lab Страницы: 33

Бренд: Omicron Lab Страницы: 21

Бренд: Omicron Lab Страницы: 22

Бренд: Vectornav Страницы: 114

Бренд: Radio Shack Страницы: 44

Бренд: Radiodetection Страницы: 2

Бренд: EUPRY Страницы: 6

Бренд: REED Страницы: 4

Бренд: PCE Instruments Страницы: 6

Бренд: Hanna Instruments Страницы: 28

Бренд: A&D Страницы: 2

K-PATENTS PR-43

Бренд: Vaisala Страницы: 54

Бренд: LaserLiner Страницы: 52

Amplitude T Series

Бренд: OTOVATION Страницы: 15

EnviroMentor Field Finder

Бренд: Radians Innova Страницы: 12

Бренд: Parkside Страницы: 165

Бренд: Bender Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды