ELTRA CS-2000 Скачать руководство пользователя страница 152

Страница: 152 / 160

Miscellaneous

152

77350

Capacitor 1µF/50V

77450

Temperature switch

77507

Ceramic tube

1/8

77525

Heating elements

77600

Grid resistor

77610

Resistor

80925

Sets of fuses

88400-
0283

Gas pump VP-6035S

90155

Combustion boats

90162

Combustion tube

90220

Tungsten

2500g

90260

Iron chips

908g

92400

Steel standards (advice %C and %S)

100g

*NOTE:

36907

Temperatur control board TH43 is an older version

36904

Temperatur control board TH43 is a newer version and fully
compatible

Pos : 9. 10 /0025 Übersc hrift en/ELTRA 1.1 Übersc hrift en11 Mai nt enanc e (2015- 12- 03 07: 57:57) @ 7\ mod_1383121708299_9. doc x @ 50516 @ 2 @ 1

6.5 Maintenance

Pos : 9. 11 /0010 ELTR A/ 0015 s ervic e_ins truc tions/C S-2000_s er vice/ 20 Misc ellaneous_CS-2000/2025 Modul Mai nt enanc e C S-2000 @ 9\ mod_1425544021010_9.doc x @ 74910 @ @ 1

–

Is the furnace closure cone still properly fixed? See chapter

“

Closing cone

”

–

Check whether the imprint of all the O-rings is at least of 2 mm thickness.

–

Is the inlet pressure regulator set on 1,5 bar ( 22.5 psi )? See chapter

“Pressure

regulators”

–

Is the other two pressure regulator set on 0,35 bar ( 5 psi )?

–

Check for leaks. See

chapter

“Leak checking”

–

Is the gas flow rate correct? See

chapter

“Gas flow controller”

–

Pressure switch: change over at about 1 bar? Measure across the leads. See

chapter

“No or low oxygen pressure”

–

Does the thermostatic control work correctly? See chapter

“IR thermostatic control”

–

Check the infrared baseline. See chapter

“Infrared base line”

–

Check whether all the screws of the generator housing are tight.

–

Check whether all four „high voltage“ stickers are still in place.

–

Check whether all plugs in the analyzer are properly plugged in.

–

Check whether all the warning labels are still attached to the side-panels.

–

Calibration of all measuring ranges.

Pos : 10 / 0010 ELTR A/------- Seit enumbruc h ----------- @ 6\ mod_1368796429449_0. doc x @ 41468 @ @ 1

Содержание CS-2000

































































































































































Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды

ELTRA CS-2000, Руководство по обслуживанию

Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды