ELTRA CS-2000 Скачать руководство пользователя страница 36

Страница: 36 / 160

Faults

High carbon results are erratic:

Even if the filter may be brushed and cleaned in ultrasonic cleaner, someday will not be able to
be cleaned any more. Filters don’t last forever.

Clean the filter and make some analyzes again. Should the results still be erratic, replace it by a
new one.

Sulfur results are not repeatable:

When the Sulfur results are not stable, but the carbon results are good, there are two possible
reasons

–

The magnesium perchlorate (anhydrone) is saturated.

Replace the complete contents of the glass tube after the corresponding furnace.

–

There is sulphuric acid in the combustion tube of the resistance furnace. Replace the
combustion tube, see chapter

“

Replacing the combustion tube

”

If the combustion tube (

) was in

use

for a

very

long time

and many samples with

high Sulfur

were analyzed, then sulfuric acid may build up in the rear-side of the combustion tube.

When the heated tube is removed together with the connector (

), a

brown fluid

can be seen in

the ceramic tube.

During the analysis, some

is trapped in this fluid, causing

non

repeatable

results. It is recommended to

clean

the furnace outlet tube.

Содержание CS-2000

































































































































































Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды

ELTRA CS-2000, Руководство по обслуживанию

Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды