ELTRA CS-2000 Скачать руководство пользователя страница 156

Страница: 156 / 160

Index

156

Index

%IR ..................................................................... 39

0.0000% .............................................................. 37

00.0ppm .............................................................. 37

1-4-4.................................................................... 33

1-4-5S ................................................................. 33

a restricted oxygen supply .................................. 14

Activating Inputs and Averages Window ............ 12

Adjusting correct furnace movement .................. 90

Adjustments ........................................................ 70

Air vent holes of the furnace ............................... 21

Analysis cicle stops too early .............................. 64

Analysis takes too long ....................................... 32

Analysis time ....................................................... 32

Analyzing ............................................................ 19

Approved methodologies to which Eltra

instruments conform ...................................... 153

Averages ............................................................. 12

Bad combustion ............................................ 27, 29

base line ............................................................. 75

Base line adjustments ......................................... 80

Base line button .................................................. 12

Base line icon ..................................................... 19

Base line window ................................................ 12

Bent plastic tube of oxygen supply ..................... 16

Blocked chemicals ........................................ 14, 15

Blocked dust filter cartridge ................................ 16

Blocked fittings .................................................... 17

Blocked flow sensor assembly ........................... 17

Blocked furnace outlet .................................. 14, 15

Blocked lance hole over the crucible .................. 15

Blocked metal dust filter...................................... 14

Blocked paper filters ..................................... 14, 15

Breaker turns off ................................................. 39

Breaker turns off at the end of the analysis ........ 43

bypass valves ..................................................... 27

C 39

Capacitor and insulator ....................................... 43

Check base lines ................................................ 12

Checking the generator tube ............................. 21

Checking the primary voltage on the high voltage

transformer ..................................................... 23

Chinch connector of thermocouple .................. 113

Chopper ........................................... 102, 104, 131
Chopper motor doesn‘t rotate ............................ 65
Chopper motor replacement ............................ 103

circuit board HF 42 ............................................. 52

Cleaning brush ................................................... 99

Closing cone ...................................................... 93

Closing cone adjustment ................................... 92

Combustion tube breaks frequently ................... 48

Combustion tube induction furnace ................... 48

Combustion tube resistance furnace ................. 48

Combustion without starting analysis ................ 50

Command to start the generator is not received 19

configuration window icon .................................. 19

Contaminated or corroded solenoid valve ......... 16

Control signal wiring ......................................... 140

Copper oxide bad quality ................................... 67

Copper oxide has a bad quality ......................... 67

Crucible or boat cracks or melts ........................ 52

Development of dust when closing the furnace . 35

deviation value too low....................................... 47

Deviation value too low ...................................... 47

Device state ....................................................... 39

device state window icon ................................... 19

Diagram Generator current vs. setpoint............. 95

Diagram Generator power vs. setpoint .............. 95

Discharging the oscillator ..................................... 8

Disposal ........................................................... 155

Disposal label ................................................... 155

Draft 11001-9002 (1-15-3-1S) ........................... 42

Draft high frequency generator (1-4-4 + 1-4-5S)

.................................................................. 25, 33

Drift too high ....................................................... 48

Drift too large ..................................................... 82

Dust or soot from the resistance furnace ........... 63

Dust trap .......................................................... 135

Dustcloud when opening the furnace ................ 44

Electronic problem Induction furnace operation 17

Electronic problem resistance furnace operation18

Electronic reasons for flow problems ................. 17

Содержание CS-2000

































































































































































Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды

ELTRA CS-2000, Руководство по обслуживанию

Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды