ELTRA CS-2000 Скачать руководство пользователя страница 82

Страница: 82 / 160

Adjustments

13.

Adjust the outputs of other cells (not golden paths) to have between 7 to 8V by adjusting
the gains of their preamplifiers.

14.

Set the jumper of the JP1 from position 2 (Test °C) to Position 3 (Analysis).

15.

Install the IR module into the analyzer.

16.

Allow sufficient time for the base lines to stabilize.

NOTICE

It is necessary to turn slowly in order for the IR sources to stabilize their temperature

with increasing IR source voltage.

–

Adjust the other cells of the module (if any) at 8V baselines or 5V to 6V in case of clean
golden paths.

–

Install the IR module into the analyzer. Allow sufficient time for the base lines to stabilize.

–

Start gas flow and check the base lines again. If any of them is significantly over 8V then
readjust.

Drift too large

–

Check the temperature regulation.

–

Unstable power supply.

–

Defective IR-source.

NOTICE

If it is shown on the display that the infrared cell's output voltage is over 10 volts then

there is a serious defect.

Содержание CS-2000

































































































































































Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды

ELTRA CS-2000, Руководство по обслуживанию

Результаты поиска

Содержание CS-2000

Отзывы:

Похожие инструкции для CS-2000

Бренды по названию

Популярные бренды